€97,000+
Vestas V27 – 225kW Fully Refurbished Wind Turbines
- Location: Denmark
- Phone: +44 (0) 7962 420898
- URL:
- Listed: 17/03/2012 2:32 pm
- Expires: 1058 days, 21 hours
Description
Fully refurbished used Wind Turbines of the legendary Vestas V27 – 225kW sourced for you to order
-
Available turbines to source for you range from 1988 – 1993
-
Prices range from €97,000 – € 115,000 EUR depending on date of manufacture
-
Towers are 30m but 40m also available on request at extra cost
-
Total prices range from €97k EUR to €115,k EUR per unit depending on age
-
Terms: Buyer will log a purchase request with us and we will source a suitable turbine for you within 90 days – ExWorks owners site
- Note: On ocassions, turbines need to be purchased from seller in ‘as is’ condition and refurbishment is then undertaken by a 3rd party affiliate refurbisher. Additional transportation costs to workshop may apply
PERFORMANCE
The expected energy yields for the Vestas V27 at various annual wind speeds (AMWS) is shown below:
| AMWS m/s | Annual MWh | Daily kWh |
| 4 | 0.128 | 351 |
| 5 | 0.255 | 699 |
| 6 | 0.411 | 1126 |
| 7 | 0.575 | 1575 |
| 8 | 0.734 | 2011 |
| 9 | 0.878 | 2405 |
The annual electricity consumption of a medium size home is in the region of 4-6 MWh or 11-16 kWh per day. At 6 m/s wind speed the Vestas V27 can provide the average annual energy needs for 100 homes.
TECHNICAL SPECIFICATIONS:
Please note that original configuration is 50hz grid frequency and would need to be converted to operate on a 60hz grid at an additional cost
- Generator Rating 225 kW at 16 m/s
- Rotor Speed 43 rpm nominal
- Cut-in Wind Speed 3.5 m/s
- Survival wind speed 56 m/s
- Rotor diameter 27m
- Rotor orientation Upwind
- Number of blades 3
- Blade material Fibreglass/polyester
- Control system Pitch controlled
- Gearbox Planetary
- Brakes Disc
- Generator Asynchronous
- Yaw control Powered
- Tower height 30 m – 40m available on request at extra cost
- Tower Free standing
Reconditioning Schedule Wind Turbines
1.
a. Tower:
i. Tower is inspected and where necessary repairs will be made inside and outside tower;
1. Inspection of security lines and connections,
2. Inspection of outside steps, correct bended steps.
3. Inspection of tower connection box, add new main twist cable. Replace tower connection box where necessary.
b. Nacelle:
i. Chassis;
1. Physical inspection of chassis and bolt connections, remove oxidation where necessary.
2. Physical inspection of subchassis, apply new layer of primer and paint against corrosion.
3. Optical and Physical inspection of rubber mountings of subchassis for anti-vibrating system
4. Attach a new layer of paint on the hood of the nacelle if necessary
ii. Yawing system;
1. Physical and optical inspection of main cogwheel on wear, where necessary smoothed teeth to assure less wear during operation
2. Opening of complete main cogwheel for cleaning and inspection of bearing, clean and inject new grease, complete new separator for ball bearings installed including dust protection.
3. Complete overhaul of yawing gearbox, all bearings replace, flexible connection inspection and adjustment.
4. Inspection and new insulation (thermical injection under high pressure) add to the yawing engine
5. Fill with new gearbox oil as prescribed by manufacturer.
6. Inspect and check for proper operation of the cable twist system.
iii. Generator;
1. Complete overhauling of generator, new bearings, windings cleaning and insulation attached (thermical injection under high pressure)
2. Check for resistance of windings and check for proper operation
3. Flexible connection of generator inspect and renew.
4. Greased bearings as prescribed by manufacturer.
iv. Main gearbox;
1. Completely overhaul gearbox, place new bearings where necessary.
2. Optical and Physical check of all cogwheels on wear and where necessary corrected. Cogwheels and axes are mounted with specifications as prescribed by Manufacturer.
3. Main axle check for haircracks with use of Dye-spray.
4. Physical and optical check of gearbox brake system for correct operation.
5. Resistance of (oil filled) gearbox to be adjusted assuring a proper operation at low windspeeds.
6. Physical and optical check on ‘back-run’ brake system, 1 replace with new brake.
7. Fill with new Castrol gearbox oil as prescribed by Manufacturer.
8. All closing parts of gearbox to be smoothened to assure a leak free operation.
v. Rotor;
1. To be overhauled completely
a. 2 New main bearings to be placed at each blade axle
b. New teflon bearings placed at each centrifugal axle where necessary
c. Shock absorbers tested for proper operation
d. Springs adjusted to dimensions as specified by Manufacturer
e. Blade angle system to be completely adjusted to factory settings, blade angles to be adjusted to 6,7 degrees
f. All covers to be checked for leakage or holes
g. Rotor to be balanced as specified by manufacturer with blades attached and numbered (under clinical conditions)
h. Rotor to be physically tested for proper operation of blade angle system and blade angle brake system
Note: During first 500 hrs of operation final power adjustments need to be made to the rotor blade system (>12m/s max 80KW output) by adjusting the springs and/or blade angle system.
vi. Blades;
1. To be cleaned completely, repaired and repainted
a. Holes to be repaired where necessary
b. Optical inspection of complete outer surface
c. Attached an anti corrosion layer for protection with 2-component paint
d. Attach a wear protection at the ‘fly’ side of the blades
c. Control housing, chassis housing and connection points and instruments
i. Main control housing
1. Physical and optical inspection and prepare for ‘Full Variable Operation’
a. Cleaning for dust
b. All connection points to be checked and cleaned from any corrosion
c. All relays to be checked for proper operation and cleaned for oxidation
d. All fuses to be checked and replaced if necessary
e. All capacitors check for proper operation
f. All transformers to be inspected and checked for resistance and proper operation
g. Mutator to be checked for proper operation
i. Diodes to be checked and replaced where necessary and diodes to be replaced where necessary
ii. Thyristors to be checked
iii. Mutator print check
iv. Cooling system to be checked
h. Transducer to be checked and adjusted to 2V between 11-12 (0 KW zero point)
i. PLC to be inspected and check for proper operation
i. Latest software in Eeproms to be loaded if necessary.
ii. Chassis housing
1. Physical and optical inspection
a. To be cleaned for dust
b. All connection points to be checked and cleaned from any corrosion
c. PLC to be inspected and checked for proper operation
2. Instruments
a. Wind vane to be checked for proper operation, bearing to be replaced (needs final adjusting during installing the wind turbine)
b. Anemometer to be checked for proper operation
c. Imbalance switch to be checked for proper operation
d. Rotations sensor to be checked for proper operation
e. Cable twist system to be checked for proper operation
DOWNLOAD REFURBISHING SCHEDULE
Reconditioning Schedule Wind Turbines.pdf
Contact Ad owner for quick sale
Time wasters and tire kickers will not be accomodated!
Disclaimers:
Above technical data is subject to technical alterations, errors and omissions
1. Wind turbine installation is highly customized according to location, set-up, seismic conditions, soil, zoning, local restrictions, and many other factors
2. Taxes, Containerizing and Shipping is not included. Estimates do not include export and other international fees.
3. This information should be used for general budgetary reasons only.
4. Pricing and availability is subject to change at any time without notice
5. The displayed location in the ‘Google Maps’ section of this ad is only an indication and does not reflect the exact location of the product offered in this advert
Related posts:
5481 total views, 5 today
9 Responses to “Vestas V27 – 225kW Fully Refurbished Wind Turbines”
Other items listed by Ralph
- Vestas V39 Wind Turbines Wanted – Sold and Bought
- AUCTION PRICE! 18 Used Mitsubishi MWT 500 – 500kW Wind Turbines For Sale
- Used Wind Turbine For Sale 3x Enercon E40 – 500kW
- WindMaster WM750kW (50Hz) Wind Turbines For Sale – One Off Opportunity
- Gamesa G87-2.0 MW T78 – Wind Turbines For Sale – 94 Units – Brand New – Immediately available
Facebook
Twitter
Youtube
LinkedIn
this offer is still up to date you?
Dear Sir,
How old are they ?? Have they been maintained by a reputable contractor and who are they so I may check on their records?
Also what is included with the turbine? Controller? inverter? etc.
I look forward to your reply.
Best Regards
Nguyen van Hiep
HCM City Viet Nam
ngavanhiep389@yahoo.com
20 Aug10
Re: 4 units of Vestas V27 – 225kW/50hz wind turbines “4 x Vestas V27 – 225kW Used Wind Turbines @ US$ 1,05,000 each
We note that all the above 4 units are still in operation in Holland. We are inteested in buying these units provided a certification from an Internationally Accrediated third Party Certifying Agency in respect of fitness and is available. We offer US$ 1,50,000/- lumpsum for all four 225/50hz machines complete in all respects.
Please reply to:
Suresh
I would like to exchange links with your site http://www.mywindpowersystem.com
Is this possible?
Dear Sir,
Can you please send details of these turbines and the maintennance records of the units. Are they still available? Are they able to be transported by sea container, i.e. multi piece tower?
Also what is included with the turbine? Controller? inverter? etc.
I look forward to your reply.
Kind Regards
Ben Clayton
SIERRA HYDROGRAPHICS
PERTH
WESTERN AUSTRALIA.
Are all towers in same condition as the one in the picture
(re rust at the top).
Is the price negotiable for the purchase of more than one machine.
Is it a one piece tower or can it be dismantled.
Why are they taking these units out of service? Are they replacing them with newer technology bigger units? How old are they ??? Have they been maintained by a reputable contractor and who are they so I may check on their records???? I see lots of rust on the top where they connect the two units How bad is it??? What about shipping when dismantaled can they be placed into containners and if so How Many containers are needed for one so I can calculate shipping, why atr the Boxes for the transformers comming with them??? as it is the complete unit!!!! Rrspectfully it is 6:35 PM right now in the states, and not 12:25 AM! Respectfully! Joseph! Wave Management Corp.
Why are they taking these units out of service? Are they replacing them with newer technology bigger units? How old are they ??? Have they been maintained by a reputable contractor and who are they so I may check on their records????
Helo, we wonder information about wind turbine production year ? Could you send some more information to email: gediminas@gepeksa.com .
Thank you,
Best regards,
JSC Gepeksa,
http://www.gepeksa.com